Alera-lighting AL 1-Light User Manual download pdf

without notice. 701 Millennium Blvd. Greenville, SC 29607 / Tel 864.678.1000 / Tech Support 864.678.1580 / Website www.aleralighting.com

Page 1/4 Rev. 01/14/14 RECESSED / AL 1-LIGHT TID

AL 1-LIGHT

Technical Installation Data

STRAIGHT RUN (VIEW SHOWN FROM WALL SIDE)

GENERAL

Work in this direction

1) Fasteners not provided for wall rail or wall plates.

2) All fasteners provided for housing, endplates, connector/aligners and electrical unit connections.

3) Pieces requiring a eld cut: Wall Rail (steel), Wall Plate (steel), Trim Rail (aluminum), Wireway

Cover (aluminum) and Diusers (plastic or aluminum).

SAMPLE: AL-1T8-P-R-LD-EPU-19.11

Consists of:

(3) 92745 Wall Rails

(3) 92746 Wall Plates

(2) 97561-00 90" Housing

(1) 97561-04 21" Housing

(1) 97559-00 ADJ Housing

(6) 114084 Reector

(2) AL8 1T8 EPU

(1) AL2 1T8 EPU L

(1) AL4 1T8 EPU ADJ

(6) 107945-04 Parabolic Louvers

(1) 97476-00 Electrical End Assembly

(2) 97416-00 End Row End Plates

STEP ONE—INSTALL WALL RAILS, PLATES, AND HOUSINGS

1) Install wall rails (see next page), fasteners not provided.

2) Install wall plates if required. Fasteners not provided.

3) Starting from right end of row (facing wall) install endplate on rst (shortest) housing with screws and nuts provided.

4) Install rst (shortest) housing and work to left installing progressively longer housings.

5) Top lip of housings tip into upper hook form of wall rail. Secure housing rmly in place by attening wall rail bend tab

over housing lip.

6) Connect hanging wires loosely.

7) Install each successive housing (shortest to longest) in similar manner, connecting housings with screws and nuts provided

and then hang loosely on hanging wires.

8) Also install trim connector/aligners at each joint as row installation progresses.

9) Install endplate on adjustable housing. Slip adjustable housing into last “xed length” housing and hang entire assembly

as a unit. Adjustable housing is then pulled out to required dimension.

10) Square-cut trim rail for adjustable housing to required length; drill three (3) each 7/32" holes using template provided

and install with sheet metal screws.

11) Level entire row on hanging wires.

Power Feed

21" Housing

90" Housing

Plug-in Connector

Service Cover

Power Access Only

Parabolic Louver

Wall Rail

Wall Plate

(where required)

Reector

(where required)

Connector Plate

Trim Connector/

Aligner

Trim Rail,

cut to length

90" Housing

Adjustable

Housing

Adjustment

Endplate

17"

Adjustment

Wireway cover

(cut to length)

Cut

Clip

Cut

Endcaps

Electrical End

Assembly

AL8-1T8-EPU

8' Electrical Unit

AL4-1T8-EPU-ADJ

4' Adjustable

Electrical Unit

AL8-1T8-EPU

8' Electrical Unit

AL2-1T8-EPU-L

2' Electrical Unit

Electrical End

Assembly

Drill (3) holes

(template provided)

Lamp Shield

Hanging

Wires

Endplate

1 2 3 4

AL 1-LIGHT 1

Summary of Contents

Page 1 - AL 1-LIGHT

Page 2

Page 3

Page 4

Comments to this Manuals

No comments

Alera-lighting AL 1-Light User Manual

Browse online or download User Manual for Lighting Alera-lighting AL 1-Light. Alera Lighting AL 1-Light User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Lighting Alera-lighting AL 1-Light